108 mm diameter, base mounted by 10 mm diameter bolt. Depth front to rear 130 mm. Fitted with 12 volt Halogen bulb 60/55 watts and 'E' marked. Also has a sidelight
Original Lucas motorcycle Headlamp, complete with light unitt and on/off switch. Painted WD green
Main and dip beams with sidelight, metal reflector, plastic backshell, gasket and wiring harness. 'E' Marked. No Rim. Fitted with 12 volt Halogen bulb 60/65 watts and 5 watt sidelight bulb. Dips to the left hand side of the road. (Comes...
5 3/4 in Light Unit with domed glass, tripod and fluted reflector. Supplied with a H4 Halogen bulb, and dust cover. On two lamp cars this is the outer main/dip beam without sidelight. Dips vertically so suitable for both Right Hand...
Lucas 5 3/4" headlamp retaining rim 54524588, 37H7024
Reproduction Light Unit only for Lucas foglamps SFT576 and WFT576, LUB106 554813
Light unit for Lucas Spotlamps SLR576 and WLR576, LUB107 554816. Matching light unit for Foglamps is also available.
For sidelight/pilot bulb on BPF Headlamps.Uses LLB989 or LLB951
Sealed beam head light unit 5 3/4". 60/37.5 watt 12 volts. This unit does not have a side light window. As Lucas SB5731 but without the pilot window. GLU135
5' is nominal size of lens. Dimension over side mounting points is 147 mm. Depth front to rear 100 mm. 12 volt 35/35 watts. There are two holes at the rear, for suitable Grommets refer to 080.085. For a spare Bulb refer to LLB3604
Made of rubber, it fits under the headlamp rim to keep out dust. Fits most 7' headlamps 552906, 3H2962
Budget priced Freestanding Headlamp shell, 7 in diameter, black shell. Used as original equipment on various Lotus 7 type cars. Supplied with chromed rim and push on connector but without the light unit to enable you to make your own...
Main and dip beams without sidelight. This headlamp does not have a full backshell, it just has a plastic mounting rim. The light unit/rear of bulb protrude through it and are, therefore, not protected as they are with a full domed...
Main and dip beams with sidelight, plastic reflector, gasket and wiring harness. 'E' Marked. No rim. Fitted with 12 volt Halogen bulb 60/65 watts and 5 watt sidelight bulb. Dips to the left hand side of the road
7 in Light Unit with flat lens, fluted reflector and tripod across the lens. Uses a Halogen H4 bulb, which is supplied , as is a dust cover. Dips vertically so it is suitable for both Right Hand Drive and Left Hand Drive.
Rubber gasket that fits between the backshell and the wing on 2 adjuster type headlamps. This gasket is 28mm wide. A wider version is avaialble should one be required. Fits with both plastic and steel backshells, 54521488
Rubber gasket that fits between the backshell and the wing on 2 adjuster type headlamps. This gasket is 32mm wide. A narrower version is available should one be required. Fits with both plastic and steel backshells, 54521487,...
Made of rubber, it fits between the backshell and the wing on 2 adjuster type headlamps, 54520919. This is the very narrow gasket - 20mm, for the less narrow version refer to 54521488 and for the wide one refer to 54521487
Plastic Backshell Assembly for 7 in headlamps, Made by Wipac, this backshell comes complete with the lamp unit retaining rim (chrome on steel) and can be used with outer rims that are retained by either a screw or a spring clip. (Spring...
Special steel Backshell for 7 in headlamps on Jaguar E Type Series I. The special feature of this backshell is the flattened or truncated section at the rear. Use in conjunction with the standard 2-Adjuster retaining rim and seating...
Chromed retaining rim for 2 adjuster type headlamps 54521913. Alternative to 010.376 which is satinless steel. If you also want the inner seating dish refer to 54058414
Chromed retaining rim and inner seating dish set for 2 adjuster headlamps, 54058414. This is the part of the 2-Adjuster headlamp in which the light unit is fitted
Set of two trimmer screws and inserts plus the spring that goes between the inner seating dish and the backshell. This kit is suitable for steel backshells 60600427
Complete with the special truncated steel backshell required to fit the Jaguar E Type Series I. E marked Halogen light unit with main and dip 60/55 watts, and with wiring harness. Dips to the left hand side of the road. The backshell is...
Made of rubber, this cover fits over the halogen bulbs to keep out dust. The cover pushes on before the plug on the wiring harness, which acts to retain the rubber cover. Fits both halogen H4 and UEC type light units
Made of rubber, it fits between the backshell and the wing on 2 adjuster type headlamps with plastic backshells. This is the narrow gasket - 24mm, for a wider gasket refer to 010.606 - 28.5mm Lucas 554279
Made of rubber, it fits between the backshell and the wing on 2 adjuster type headlamps with plastic backshells. This is the wide gasket - 28.5mm, for a narrower gasket refer to 010.605 - 24mm 554280
Chromed round headed screw used to retain the finishing rim on 7 inch headlamps. Fits both plastic and steel backshells
For Side Mounting. LIMITED NUMBER AVAILABLE
Reproduction of the Lucas 7' Headlamp SS700P, complete with light unit, panel, switch and ammeter. Black enamel shell with chrome rim. As fitted to many British motorcycles
Stainless steel Headlamp Visor to suit 7 in diameter headlamp. No drilling, fits under rim. Sold singly, for a pair refer to 090.321
A quality reproduction of the Lucas 7 in Spotlamp SLR700, Chrome back and curved glass. For a spare bulb (double contact) refer to LLB326
Budget priced Freestanding Headlamp Shell, 7 in diameter, chrome finish. Used as original equipment on various Lotus 7 type cars. Supplied with rim and push on connector but without the light unit to enable you to make your own choice of...
Stainless steel retaining rim for 2 adjuster type headlamps. The part of the rim that shows is polished. Alternative to 54521913 which is chromed
Sealed beam head light unit 7". 65/55 watt 12 volts. This unit has a side light window. LHD SB7029 but with a side light window